---

Click here to go to the applet.

This java applet is an electronic circuit simulator. When the applet starts up you will see a simple LRC circuit. The green color indicates positive voltage. The gray color indicates ground. A red color indicates negative voltage. The moving yellow dots indicate current.

To turn a switch on or off, just click on it. If you move the mouse over any component of the circuit, you will see a short description of that component and its current state in the lower right corner of the window. To modify a component (say, to change the resistance of one of the resistors), move the mouse over it, click the right mouse button (or control-click, if you have a Mac) and select “Edit”.

There are three graphs at the bottom of the window; these act like oscilloscopes, each one showing the voltage and current across a particular component. Voltage is shown in green, and current is shown in yellow. The current may not be visible if the voltage graph is on top of it. The peak value of the voltage in the scope window is also shown. Move the mouse over one of the scope views, and the component it is graphing will be highlighted. To modify or remove a scope, click the right mouse button over it. To view a component in the scope, click the right mouse button over the component and select “View in Scope”.

If the simulation is moving too slowly or too quickly, you can adjust the speed with the “Simulation Speed” slider.

---

The Circuits menu can be used to view some interesting pre-defined circuits. Once a circuit is selected, you may modify it all you want. The choices are:

• Basics
• Resistors: this shows some resistors of various sizes in series and parallel.
• Capacitor: this shows a capacitor that you can charge and discharge by clicking on the switch.
• Inductor: this shows an inductor that you can charge and discharge by clicking on the switch.
• LRC Circuit: this shows an oscillating circuit with an inductor, resistor, and capacitor. You can close the switch to get current moving in the inductor, and then open the switch to see the oscillation.
• Voltage Divider: this shows a voltage divider, which generates a reference voltage of 7.5V, 5V, and 2.5V from the 10V power supply.
• Thevenin’s Theorem states that the circuit on top is equivalent to the circuit on the bottom.
• Norton’s Theorem states that the circuit on top is equivalent to the circuit on the bottom.
• A/C Circuits
• Capacitor: this shows a capacitor connected to an alternating voltage source.
• Inductor
• Caps of Various Capacitances: shows the response of three different capacitors to the same frequency.
• Caps w/ Various Frequencies: shows the response of three equal capacitors to three different frequencies; the higher the frequency, the larger the current.
• Inductors of Various Inductances: shows the response of three different inductors to the same frequency.
• Inductors w/ Various Frequencies: shows the response of three equal inductors to three different frequencies: the lower the frequency, the larger the current.
• Impedances of Same Magnitude: shows a capacitor, an inductor, and a resistor that have impedances of equal magnitude (but different phase). The peak current is the same in all three cases.
• Series Resonance: shows three identical LRC circuits being driven by three different frequencies. The middle one is being driven at the resonance frequency (shown in the lower right corner of the screen as “res.f”). The top one is being driven at a slightly lower frequency, and the bottom one has a slightly higher frequency. The peak voltage in the middle circuit is very high because it is resonating with the source.
• Parallel Resonance: these three circuits have the inductor, resistor, and capacitor in parallel instead of series. In this case, the middle circuit is being driven at resonance, which causes the current there to be lower than in the other two cases (because the impedance of the circuit is highest at resonance).
• Passive Filters
• High-Pass Filter (RC). The original signal is shown at the lower left, and the filtered signal (with the low-frequency part removed) is shown to the right. The breakpoint (-3 dB point) is shown at the lower right, as “f.3db”. The input for this filter consists of two AC sources back-to-back, which adds their voltages together. In real life, you can’t do this, but it comes in handy in this applet.
• Low-Pass Filter (RC).
• High-Pass Filter (RL). This high-pass filter uses an inductor rather than a capacitor.
• Low-Pass Filter (RL).
• Band-Pass Filter: this filter passes a range of frequencies close to the resonance frequency (shown at the lower right, as “res.f”).
• Notch Filter: Also known as a band-stop filter, this circuit filters out a range of frequencies close to the resonance frequency.
• Twin-T Filter: This filter does a very good job of filtering out 60 Hz signals.
• Other Passive Circuits
• Series/Parallel
1. Inductors in Series. The circuit at left is equivalent to the circuit at right.
2. Inductors in Parallel.
3. Caps in Series.
4. Caps in Parallel.
• Transformers
1. Transformer: A basic transformer circuit with an equal number of windings in each coil.
2. Transformer w/ DC: Here we try to pass a DC current through a transformer.
3. Step-Up Transformer: Here we step 10 V up to 100 V.
4. Step-Down Transformer: Here we step 120 V down to 12 V.
• 3-Way Light Switches: shows how a light bulb can be turned on and off from two locations.
• 3- and 4-Way Light Switches: shows how a light bulb can be turned on and off from three locations.
• Differentiator: shows how a capacitor can act as a differentiator, reflecting changes in voltage.
• Wheatstone Bridge: shows a balanced Wheatstone bridge. If the bridge were not balanced, current would be flowing across from one leg to the other.
• Critically Damped LRC.
• Current Source: shows a source that keeps the current through the circuit constant regardless of the switch positions.
• Inductive Kickback: In this circuit, we have a switch that controls the supply of current to an inductor. An inductor resists any changes in current. If you open the switch, the inductor tries to maintain the same current; it does this by charging the capacitance between the contacts of the switch. (Any two wires in close proximity have some parasitic capacitance between them.) There is a small capacitor (much larger than the actual value) across the switch terminals to simulate this. When you open the switch, the voltage goes very high; in real life, this would cause arcing.
• Blocking Inductive Kickback: shows how inductive kickback can be blocked with a “snubber” circuit.
  
  
• Power Factor: This circuit shows an inductor being driven by an AC voltage. The colors indicate power consumption; red means that a component is consuming power, and green means that the component is contributing power. The left side of the circuit represents the power company’s side, and the right side represents a factory (with a large induction motor).
  
  The highly inductive load is causing the power company to work a lot harder than normal for a given amount of power delivered. The graph on the left indicates the power lost in the power company’s equipment (the resistor at top left). The graph in the middle is the power delivered to the factory. The graph on the right is the power delivered to the inductor (and then returned, causing the time average of power delivered to be zero).
  
  Even though a peak power of 40 mW is being delivered to the factory, 200 mW is being dissipated in the power company’s wires. This is why power companies charge extra for inductive loads.
  
  
• Power Factor Correction: Here a capacitor has been added to the circuit, causing far less energy to be wasted in the power company’s wires (aside from an initial spike to charge the capacitor).
• Resistor Grid: shows current flowing in a two-dimensional grid of resistors.
• Resistor Grid 2.
• Coupled LC's
1. LC Modes(2): Shows both modes of two coupled LC circuits.
2. Weak Coupling.
3. LC Modes(3): Shows all 3 modes of 3 coupled LC circuits.
4. LC Ladder: This circuit is a simple model of a transmission line. A pulse propagates down the length of the ladder like a wave. The resistor at the end has a value equal to the characteristic impedance of the ladder (determined by the ratio of L to C), which causes the wave to be absorbed. A larger resistance or an open circuit will cause the wave to be reflected; a smaller resistance or a short will cause the wave to be reflected negatively. See the Feynman Lectures 22-6, 7.
• Phase-Sequence Network: This circuit generates a series of sine waves with a phase difference of 90°.
• Diodes
• Half-Wave Rectifier: This circuit removes the negative part of an input waveform.
• Full-Wave Rectifier: This circuit replaces a waveform with its absolute value.
• Full-Wave Rectifier w/ Filter: This circuit smoothes out the rectified waveform, doing a pretty good job of converting AC to DC.
• Diode I/V Curve: This demonstrates the response of a diode to an applied voltage. The voltage source generates a sawtooth wave, which starts out at –800 mV and slowly rises to 800 mV, and then immediately drops back down again.
• Diode Limiter.
• DC Restoration. This takes an AC signal and adds a DC offset, making it a positive signal.
• Blocking Inductive Kickback: shows how inductive kickback can be blocked with a diode.
• Spike Generator.
• Voltage Multipliers
1. Voltage Doubler: Doubles the voltage in the AC input signal (minus two diode drops), and turns it into DC.
2. Voltage Doubler 2
3. Voltage Tripler
4. Voltage Quadrupler
• AM Detector: This is a “crystal radio”, an AM radio receiver with no amplifier. The raw antenna feed is shown in the first scope slot in the lower left. The inductor and the capacitor C1 are tuned to 3 kHz, the frequency shown in the lower right as “res.f”. This picks up the carrier wave shown in the middle scope slot. A diode is used to rectify this, and the C2 capacitor smoothes it out to generate the audio signal in the last scope slot (which is simply a 12 Hz sine wave in this example). By experimenting with the value of C1’s capacitance, you can pick up two other “stations” at 2.71 kHz and 2.43 kHz.
• Triangle-to-Sine Converter
• Transistors
• Switch.
• Emitter Follower.
• Astable Multivibrator: A simple oscillator. The applet has trouble simulating this circuit, so there might be a slight delay every time one of the transistors switches on.
• Bistable Multivibrator (Flip Flop): This circuit has two states; use the set/reset switches to toggle between them.
• Monostable Multivibrator (One-Shot): When you hit the switch, the output will go to 1.7 V for a short time, and then drop back down.
• Common-Emitter Amplifier: This circuit amplifies the voltage of the input signal by about 10 times.
• Unity-Gain Phase Splitter: Outputs two signals 180° out of phase from each other.
• Schmitt Trigger.
• Current Source: The current is the same regardless of the switch position.
• Current Source Ramp: Uses a current source to generate a ramp waveform every time you hit the switch.
• Current Mirror: The current on the right is the same as the current on the left, regardless of the position of the right switch.
• Differential Amplifiers
1. Differential Input: This circuit subtracts the first signal from the second and amplifies it.
2. Common-Mode Input: This shows a differential amplifier with two equal inputs. The output should be a constant value, but instead the input waveforms make it through to the output (attenuated rather than amplified). (When both inputs change together, that is called “common-mode input”; the “common-mode rejection ratio” is the ability of a differential amplifier to ignore common-mode signals and amplify only the difference between the inputs.)
3. Common-Mode w/Current Source: This is an improved differential amplifier that uses a current source as a load. The common-mode rejection ratio is very good; the circuit amplifies the small differences between the two inputs, and ignores the common-mode signal.
• Push-Pull Follower: This is another type of emitter follower.
• Oscillators
1. Colpitts Oscillator
2. Hartley Oscillator
3. Emitter-Coupled LC Oscillator
• JFETs
• JFET Current Source
• JFET Follower: This is like an emitter follower, except that the output is 3V more positive than the input.
• JFET Follower w/zero offset
• Common-Source Amplifier
• Volume Control: Here the JFET is used like a variable resistor.
• MOSFETs
• CMOS Inverter: The white “H” is a logic input. Click on it to toggle its state. “H” means “high” (5 V) and “L” means “low” (0 V). The output of the inverter is shown at right, and is the opposite of the input. In this (idealized) simulation, the CMOS inverter draws no current at all.
• CMOS Inverter (w/capacitance): In reality, there are two reasons that CMOS gates draw current. This circuit demonstrates the first reason: capacitance between the MOSFET gate and its source and drain. It requires current to charge this capacitance, which consumes power. It also causes a short delay when changing state.
• CMOS Inverter (slow transition): The other reason that CMOS gates draw current is that both transistors will conduct at the same time when the input is halfway between high and low. This causes a current spike when the input is in transition. In this circuit, there is a low-pass filter on the input which causes it to transition slowly, so you can see the spike.
• CMOS Transmission Gate: This circuit will pass any signal, even an analog signal (as long as it stays between 0 and 5 V) when the gate input is “H”. When it’s “L”, then the gate acts as an open circuit.
• CMOS Multiplexer: This circuit uses two transmission gates to select one of two inputs. If the logic input is “H”, then the output is a 40Hz triangle wave. If it’s “L”, then the output is a 80Hz sine wave.
• Sample-and-Hold: Click and hold the “sample” button to sample the input. When you release the button, the output level will be held constant.
• Delayed Buffer: This circuit delays any changes in its input for 15 microseconds.
• Leading-Edge Detector
• Switchable Filter: Click the “L” to select from two different low-pass filters.
• Voltage Inverter
• Inverter Amplifier: This shows how a CMOS inverter can be used as an amplifier.
• Inverter Oscillator
• Op-Amps
• Amplifiers
1. Inverting Amplifier: This one has a gain of –3.
2. Non-Inverting Amplifier
3. Follower
4. Differential Amplifier
5. Summing Amplifier
• Oscillators
1. Relaxation Oscillator
2. Phase-Shift Oscillator
3. Triangle Wave Generator
4. Sine Wave Generator
5. Sawtooth Wave Generator
6. Voltage-Controlled Oscillator: Here the frequency of oscillation depends on the input (shown in the scope on the left). The oscillator outputs a square wave and a triangle wave.
• Half-Wave Rectifier: An active rectifier that works on voltages smaller than a diode drop.
• Full-Wave Rectifier
• Peak Detector: This circuit outputs the peak voltage of the input. Whenever the input voltage is higher than the output, the output will be adjusted upward to match. Press the switch marked “reset” to reset the peak voltage back to 0.
• Integrator
• Differentiator
• Schmitt Trigger
• Negative Impedance Converter: Converts the resistor to a “negative” resistor. In the first graph, note that the current is 180° out of phase with the voltage.
• Gyrator: The top circuit simulates the bottom circuit without using an inductor.
• Capacitance Multiplier: This circuit allows you to simulate a large capacitor with a smaller one. The effective capacitance of the top circuit is C1 x (R1/R2), and the effective resistance is R2.
• Howland Current Source
• I-to-V Converter: The output voltage depends on the input current, which you can adjust with the switches.
• 741 Internals: The implementation of a 741 op-amp.
• 555 Timer Chip
• Square Wave Generator
• Internals: The implementation of a 555 chip, acting as a square wave oscillator
• Sawtooth Oscillator
• Low-duty-cycle Oscillator: produces short pulses.
• Monostable Multivibrator: This is a one-shot circuit that will produce a timed pulse when you click the “H”.
• Pulse Position Modulator: Produces pulses whose width is proportional to the input voltage.
• Active Filters
• VCVS Low-Pass Filter: An active Butterworth low-pass filter.
• VCVS High-Pass Filter
• Switched-Capacitor Filter: A digital filter, implemented using capacitors and analog switches.
• Logic Families
• RTL Logic Family
1. RTL Inverter: The white “H” is a logic input. Click on it to toggle its state. “H” means “high” (3.6 V) and “L” means “low” (0 V). The output of the inverter is shown at right, and is the opposite of the input.
2. RTL NOR: The three inputs are at the bottom, and the output is to the right. The output is “L” if any of the inputs are “H”. Otherwise it’s “H”.
3. RTL NAND: The output is “H” unless all three inputs are “H”, and then it’s “L”.
• DTL Logic Family
1. DTL Inverter
2. DTL NAND
3. DTL NOR
• TTL Logic Family
1. TTL Inverter
2. TTL NAND
3. TTL NOR
• NMOS Logic Family
1. NMOS Inverter
2. NMOS Inverter 2: This uses a second MOSFET instead of a resistor, to save space on a chip.
3. NMOS NAND
• CMOS Logic Family
1. CMOS Inverter
2. CMOS NAND
3. CMOS NOR
4. CMOS XOR
5. CMOS Flip-Flop (or latch): This circuit consists of two CMOS NAND gates.
6. CMOS Master-Slave Flip-Flop
• ECL Logic Family
1. ECL NOR/OR
• Combinational Logic
• Exclusive OR (XOR)
• Half Adder
• Full Adder
• 1-of-4 Decoder
• 2-to-1 Mux: This multiplexer uses two tri-state buffers connected to the output.
• Majority Logic: The output is high if a majority of the inputs are high.
• 2-Bit Comparator: Tells you if the two-bit input A is greater than, less than, or equal to the two-bit input B.
• 7-Segment LED Decoder
• Sequential Logic
• Flip-Flops
1. SR Flip-Flop
2. Clocked SR Flip-Flop
3. Master-Slave Flip-Flop
4. Edge-Triggered D Flip-Flop: This circuit changes state when the clock makes a positive transistion.
• Counters
1. 4-Bit Ripple Counter
2. 8-Bit Ripple Counter
3. Synchronous Counter
4. Decimal Counter
5. Gray Code Counter
6. Johnson Counter
• Divide-by-2: Divides the input frequency by 2.
• Divide-by-3
• LED Flasher: This circuit uses a Johnson counter to flash some LED’s in a back and forth pattern.
• Traffic Light
• Dynamic RAM: This is a simple model of a dynamic RAM chip. To read from the chip, select the bit you want using the row select lines. To write, select the data bit you want to write, and click the “write” switch. To refresh a bit, click the “refresh” switch.
• Analog/Digital
• Flash ADC: This is a direct-conversion, or “flash” analog-to-digital converter.
• Binary-Weighted DAC: Converts a four-bit binary number to a negative voltage.
• R-2R Ladder DAC
• Digital Sine Wave
• Phase-Locked Loops
• XOR Phase Detector: Shows an XOR gate being used as a type I phase detector. The output is high whenever the two input signals are not in phase.
• Type I PLL: This phase-locked loop circuit consists of an XOR gate (the phase detector), a low-pass filter (the resistor and capacitor), a follower (the op-amp), and a voltage-controlled oscillator chip. The voltage-controlled oscillator outputs a frequency proportional to the input voltage. After the PLL circuit locks onto the input frequency, the output frequency will be the same as the input frequency (with a small phase delay).
• Phase Comparator (Type II): Shows a more sophisticated phase detector, which has no output when the inputs are in phase, but outputs high (5V) when input 1 is leading input 2, and low (0V) when input 2 is leading input 1. The phase comparator and VCO in this applet are based on the 4046 chip.
• Phase Comparator Internals.
• Type II PLL: Shows a phase-locked loop with a type II phase detector. If you adjust the input frequency, the output should lock onto it in a short time.
• Type II PLL (fast): Just a faster simulation of the type II PLL.
• Frequency Doubler

To add a new component to the circuit, click the right mouse button on an unused area of the window. This will bring up a menu that allows you to select what component you want. Then click where you want the first terminal of the component, and drag to where you want the other terminal. The menu items allow you to create:

· wires

· resistors; you can adjust the resistance after creating the resistor by clicking the right mouse button and selecting “Edit”

· capacitors; you can adjust the capacitance using “Edit”

· inductors, switches, transistors, etc.

· voltage sources, in either 1-terminal or 2-terminal varieties. The 1-terminal versions use ground as the other terminal. By clicking the right mouse button and selecting “Edit”, you can modify the voltage and the waveform of the voltage source, changing it to DC, AC (sine wave), square wave, triangle, sawtooth, or pulse. If it’s not a DC source, you can also change the frequency and the DC offset.

· op-amps, with power supply limits of –15V and 15V assumed (not shown). The limits can be adjusted using “Edit”.

· text labels, which you can modify with the “Edit” dialog

· scope probes; these have no effect on the circuit, but if you select them and use the right mouse menu item “View in Scope”, you can view the voltage difference between the terminals.

Also in the “Other” submenu, there are some items that allow you to click and drag sections of the circuit around. Save your work before trying these.

The File menu allows you to import or export circuit description files. Java security restrictions usually prevent an applet from writing files to a user’s computer. So instead, when you select the File->Export menu item, the applet brings up a window containing the description file for the circuit, which you can copy and paste into another application. You can paste the file back into the window later and click Import to load it.

The Reset button resets the circuit to a reasonable state. The Stopped checkbox allows you to stop the simulation. The Simulation Speed slider allows you to adjust the speed of the simulation. If the simulation isn’t time-dependent (that is, if there are no capacitors, inductors, or time-dependent voltage sources), then this won’t have any effect. The Current Speed slider lets you adjust the speed of the dots, in case the currents are so weak (or strong) that the dots are moving too slowly (or too quickly).

To edit one of the scope views, click the right mouse button on it to view a menu. The menu items allow you to remove a scope view, speed up or slow down the display, adjust the scale, select what value(s) you want to view, etc.

Here are some errors you might encounter when using the simulator:

· Voltage source loop with no resistance! – this means one of the voltage sources in your circuit is shorted. Make sure there is some resistance across every voltage source.

· Capacitor loop with no resistance! – it’s not allowed to have any current loops containing capacitors but no resistance. For example, capacitors connected in parallel are not allowed; you must put a resistor in series with them. Shorted capacitors are allowed.

· Singular matrix! – this means that your circuit is inconsistent (two different voltage sources connected to each other), or that the voltage at some point is undefined. It might mean that some component’s terminals are unconnected; for example, if you create an op-amp but haven’t connected anything to it yet, you will get this error.

· Convergence failed! – this means the simulator can’t figure out what the state of the circuit should be. Just click Reset and hopefully that should fix it. Your circuit might be too complicated, but this happens sometimes even with the examples.

Click here to go to the applet.

---

java@falstad.com